Empirisoft Support

    Welcome to Empirisoft Support
Results 1 to 2 of 2

Thread: Interface with a BioPac System

  1. #1
    Join Date
    Nov 2005
    Posts
    294

    Interface with a BioPac System

    [edited from a support email]

    We're trying to get MediaLab to interface with a biopac physiology
    system using a TTL out.

    They sent us to the following link for the cabling we need:

    http://biopac.com/product.cgi?type=view&item=STP35A

    But, $90 seems rather pricey.

    I thought I'd check with you to see if you thought that the parameter
    we've used to communicate with other systems using TTL-out:

    <1:888:500>

    This should also work using any DB-25 Male and Female cable (which we can
    get for about $10 at CDW).
    Last edited by JEC; 11-07-2006 at 03:40 PM.

  2. #2
    Join Date
    Nov 2005
    Posts
    294
    It's been a while since I've spent time in the Biopac system, but here's
    what I remember:

    1. We do have many customers who have successfully made the interface.

    2. There was at one time an issue with the Biopac system not registering TTL input. We discovered that some newer computer systems (in particular, laptops) only output 3.3V on the parallel port, rather than the old standard of 5v.

    Thus, even when the MediaLab / DirectRT computer was connected properly to the Biopac interface, signals weren't properly recorded. This may have been resolved in the past few months.

    You can verify the output of your parallel port by sending data with our IOTester utility and measuring the output voltage with an oscilloscope or multimeter.

    Accessory parallel ports can be purchased from CompUSA or similar for $10 - $20.

    3. The pinout on the cable they're selling is different than the $10 CDW cable. Typically all 25 pins are connected straight through in a standard cable. This custom one has some pins swapped.

    However, it appears that it will work right out of the box. To save time, it may be a good option. If someone in your lab is handy with a soldering iron, however, the proper cable can be made for only a few dollars.

    4. For a basic MediaLab start/stop control setup, you just need to connect pin 2 of your MediaLab computer's parallel port to a TTL input on the biopac box and any one of parallel port pins 18-25 to ground on the biopac box.

    You might also check out this post

    http://www.empirisoft.com/Support/sh...ht=eye+tracker

    for more details on sending TTL signals from DirectRT and MediaLab.

Similar Threads

  1. Computer System and Setup Recommendations? (case 2912)
    By jarvis24 in forum Pre-Sales and Licensing FAQ
    Replies: 9
    Last Post: 10-25-2012, 10:42 AM
  2. How does your pricing/licensing system work?
    By jarvis24 in forum Pre-Sales and Licensing FAQ
    Replies: 2
    Last Post: 03-19-2007, 10:27 AM
  3. Sample Script for an Eye-Tracking Interface
    By JEC in forum Hardware: How Do I...
    Replies: 1
    Last Post: 03-19-2007, 09:34 AM
  4. Resolution not supported on this system message
    By jarvis24 in forum DirectRT Older Versions: Troubleshooting
    Replies: 2
    Last Post: 06-14-2006, 04:18 PM
  5. How Do I Interface With an Eye-Tracking System?
    By JEC in forum Hardware: How Do I...
    Replies: 1
    Last Post: 02-17-2006, 01:15 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •